* tesla safety cleanup + long WIP
* more long safety
* longitudinal safety tests
* fix misra
* add safety for main bus DAS_control
* acc_state is not enabled
* fix tests
* we don't want this
* fix Tesla common test
* python: disable power save by default when setting safety mode
* no need to set power save manually
* Update python/__init__.py
Co-authored-by: Adeeb Shihadeh <adeebshihadeh@gmail.com>
* Extend ISO-TP subsequent frame timeout, add response pending timeout and extra debug info
* Change response_pending to local variable, move response_pending_timeout to UdsClient, update ISO-TP debug output
* Set UDS request pending timeout to 6 seconds (ISO 14229-2:2013 section 7.2 recommended value + 1 second latency)
* manage response pending in single location
* more generous response pending timeout
* add tx timeout
* fix lint error
* fix rx addr for 29 bit addrs
* fix linting issue
Co-authored-by: Martin Lillepuu <martin@mlp.ee>
* H7 drivers
* Include H7 into the code
* fix flash write for H7
* get serial from flasher.h from F4 and H7
* flash.sh and recover.sh for gen3
* add set_data_speed for BRS CAN FD
* build all fws
* gen3 to panda lib
* gen3 name in scons project
* disable fd can and brs
* gen3 to CI tests
* jenkins fix for new tests and build_all
* fix pedal test
* pedal in panda tests again...
* cleanup llfdcan.h
* cleanup clock.h
* Add LDORDY bit check instead of delay
* missing define in stm32h735xx.h lib
* board_id helper
* enable debug detection again
* clean gpio inits
* fix board_id helper, make cleaner
* comment MCUs in stm lib for faster misra
* target MCU
* misra-5.5
* improve headers and misra speed
* cleanup CI tests
* change naming from gen3 to h7
* readable if statement
* cleanup llusb.h
* only cycle one transceifer in bus-off
* move unused funcs to common header
* bus_off_err reset
* misra 10.4 fdcan
* extern to can_data_speed variable
* limit can_data_speed array size to 3
* reinit fd can on data speed change
* Improve test with ELM327 and extaddr check
* bugfix for fdcan
* panda python config naming
* abstracted init request in llfdcan
* misra fdcan
* Improve llusb.h for H7
* Remove non-EON panda build
* missed that
* fixup readme
* more readme
* simplify ci
* add USB command to disable heartbeat checks in debug mode
* clean that up too
* more cleanup
* fix path
* disable heartbeat in set_safety_mode
* more red
* remove one more EON ref
* remove unused wifi tests
* remove that one too
* no bootmode from ESP
* clean that up
* remove two more wifi tests
* remove boardesp and esptool
* esp_gps -> gps
* missed those
* remove esptool refs
* remove esp certs
* no more wifi
* that was old
* cleanup jenkins dockerfile
* fix linter
* remove more wifi refs
* clone panda jungle from github
* no copy
* always default esp to off
* k-line slow init
* k-line slow init LED bit blink
* fix misra violations
* better names for k-line methods
* debug prints match names
* switch to timer
* use TIM4 until I figure out TIM5
* tickle faster
* fix bit bug and add stop bit
* TIM5 working
* USB return after addr sent
* fix l-line reset
* fix misra violations
* blink for the ones instead of the zeros
* k-line 5 baud fault type
* lin check
* use TIM5 or wakeup
* better names
* enable UART RX interrupts
* update debug prints for python3
* improve kline functions and fix checksum
* k-line wake-up conforming to KWP2000 fast init
* fix timing
* toggle k and l line together by default
* k-line wakeup using timer
* k and l were flipped
* fix misra compliance
* fix W391
* E262
* E703
* W293
* some E
* E231
* some more E
* E225
* more E
* E252
* no tabs
* more tabs
* E701
* uds.py
* almost all of them
* only e265 left
* not sure why this is triggering on commented out code
* ignore esptool
* Add pre commit checks
* untested but should work
* fix typo in dockerfile
* add sqlite
* add pylintrc to ignore usb1 members
* Typo in stage name
* Move to requirements
