77 lines
3.4 KiB
C
77 lines
3.4 KiB
C
/*
|
|
HSE: 25MHz
|
|
PLL1Q: 80MHz (for FDCAN)
|
|
HSI48 enabled (for USB)
|
|
CPU: 240MHz
|
|
CPU Systick: 240MHz
|
|
AXI: 120MHz
|
|
HCLK3: 60MHz
|
|
APB3 per: 60MHz
|
|
AHB1,2 per: 120MHz
|
|
APB1 per: 60MHz
|
|
APB1 tim: 120MHz
|
|
APB2 per: 60MHz
|
|
APB2 tim: 120MHz
|
|
AHB4 per: 120MHz
|
|
APB4 per: 60MHz
|
|
PCLK1: 60MHz (for USART2,3,4,5,7,8)
|
|
*/
|
|
|
|
void clock_init(void) {
|
|
// Set power mode to direct SMPS power supply(depends on the board layout)
|
|
#ifndef STM32H723
|
|
register_set(&(PWR->CR3), PWR_CR3_SMPSEN, 0xFU); // powered only by SMPS
|
|
#else
|
|
register_set(&(PWR->CR3), PWR_CR3_LDOEN, 0xFU);
|
|
#endif
|
|
// Set VOS level (VOS3 to 170Mhz, VOS2 to 300Mhz, VOS1 to 400Mhz, VOS0 to 550Mhz)
|
|
register_set(&(PWR->D3CR), PWR_D3CR_VOS_1 | PWR_D3CR_VOS_0, 0xC000U); //VOS1, needed for 80Mhz CAN FD
|
|
while ((PWR->CSR1 & PWR_CSR1_ACTVOSRDY) == 0U);
|
|
while ((PWR->CSR1 & PWR_CSR1_ACTVOS) != (PWR->D3CR & PWR_D3CR_VOS)); // check that VOS level was actually set
|
|
|
|
// Configure Flash ACR register LATENCY and WRHIGHFREQ (VOS0 range!)
|
|
register_set(&(FLASH->ACR), FLASH_ACR_LATENCY_2WS | 0x20U, 0x3FU); // VOS2, AXI 100MHz-150MHz
|
|
// enable external oscillator HSE
|
|
register_set_bits(&(RCC->CR), RCC_CR_HSEON);
|
|
while ((RCC->CR & RCC_CR_HSERDY) == 0U);
|
|
// enable internal HSI48 for USB FS kernel
|
|
register_set_bits(&(RCC->CR), RCC_CR_HSI48ON);
|
|
while ((RCC->CR & RCC_CR_HSI48RDY) == 0U);
|
|
// Specify the frequency source for PLL1, divider for DIVM1, DIVM2, DIVM3 : HSE, 5, 5, 5
|
|
register_set(&(RCC->PLLCKSELR), RCC_PLLCKSELR_PLLSRC_HSE | RCC_PLLCKSELR_DIVM1_0 | RCC_PLLCKSELR_DIVM1_2 | RCC_PLLCKSELR_DIVM2_0 | RCC_PLLCKSELR_DIVM2_2 | RCC_PLLCKSELR_DIVM3_0 | RCC_PLLCKSELR_DIVM3_2, 0x3F3F3F3U);
|
|
|
|
// *** PLL1 start ***
|
|
// Specify multiplier N and dividers P, Q, R for PLL1 : 48, 1, 3, 2 (clock 240Mhz, PLL1Q 80Mhz for CAN FD)
|
|
register_set(&(RCC->PLL1DIVR), 0x102002FU, 0x7F7FFFFFU);
|
|
// Specify the input and output frequency ranges, enable dividers for PLL1
|
|
register_set(&(RCC->PLLCFGR), RCC_PLLCFGR_PLL1RGE_2 | RCC_PLLCFGR_DIVP1EN | RCC_PLLCFGR_DIVQ1EN | RCC_PLLCFGR_DIVR1EN, 0x7000CU);
|
|
// Enable PLL1
|
|
register_set_bits(&(RCC->CR), RCC_CR_PLL1ON);
|
|
while((RCC->CR & RCC_CR_PLL1RDY) == 0U);
|
|
// *** PLL1 end ***
|
|
|
|
//////////////OTHER CLOCKS////////////////////
|
|
// RCC HCLK Clock Source / RCC APB3 Clock Source / RCC SYS Clock Source
|
|
register_set(&(RCC->D1CFGR), RCC_D1CFGR_HPRE_DIV2 | RCC_D1CFGR_D1PPRE_DIV2 | RCC_D1CFGR_D1CPRE_DIV1, 0xF7FU);
|
|
// RCC APB1 Clock Source / RCC APB2 Clock Source
|
|
register_set(&(RCC->D2CFGR), RCC_D2CFGR_D2PPRE1_DIV2 | RCC_D2CFGR_D2PPRE2_DIV2, 0x770U);
|
|
// RCC APB4 Clock Source
|
|
register_set(&(RCC->D3CFGR), RCC_D3CFGR_D3PPRE_DIV2, 0x70U);
|
|
|
|
// Set SysClock source to PLL
|
|
register_set(&(RCC->CFGR), RCC_CFGR_SW_PLL1, 0x7U);
|
|
while((RCC->CFGR & RCC_CFGR_SWS) != RCC_CFGR_SWS_PLL1);
|
|
//////////////END OTHER CLOCKS////////////////////
|
|
|
|
// Configure clock source for USB (HSI48)
|
|
register_set(&(RCC->D2CCIP2R), RCC_D2CCIP2R_USBSEL_1 | RCC_D2CCIP2R_USBSEL_0, RCC_D2CCIP2R_USBSEL);
|
|
// Configure clock source for FDCAN (PLL1Q at 80Mhz)
|
|
register_set(&(RCC->D2CCIP1R), RCC_D2CCIP1R_FDCANSEL_0, RCC_D2CCIP1R_FDCANSEL);
|
|
// Configure clock source for ADC1,2,3 (per_ck(currently HSE))
|
|
register_set(&(RCC->D3CCIPR), RCC_D3CCIPR_ADCSEL_1, RCC_D3CCIPR_ADCSEL);
|
|
//Enable the Clock Security System
|
|
register_set_bits(&(RCC->CR), RCC_CR_CSSHSEON);
|
|
//Enable Vdd33usb supply level detector
|
|
register_set_bits(&(PWR->CR3), PWR_CR3_USB33DEN);
|
|
}
|