* civic 2022
* remove
* maybe not the right way
* Honda Radarless: add tests
* update
* different bus
* other bus
* Revert "other bus"
This reverts commit 691e045f87.
* add new HUD message
* add
* different bus
* correct freq
* small updates
* comma
* remove
* remove for now
* missing
* not needed
* make into a safety param and clean up
* this can be reverted
* clean up tests (something's broken)
* fix some errors
* this message doesn't exist on any bus
* this car doesn't have BRAKE_MODULE
* make safety more explicit and fix button safety
* fix some tests
* fix tests
formatting
clean up
* radarless uses SCM_FEEDBACK too
* fix tx msgs, clean up, make test common between bosch tests
* misra
* Fix python linting errors
add comment
* not sure where that came from
* add comments
add comments
* we can guarantee honda_bosch_long is true only if not radarless
* these are the same! 🎉
* use updated route with correct tx msgs
* helper pt bus function
* this is explained above
* use function
* no more blocked messages!
* bump openpilot
* comment
* line too long
* needs system
* send on bus 0
* Camera needs bus 2 for buttons
This reverts commit f90db5d359.
* fix button tests
* bump openpilot
* move this down
* make this explicit
* comments
Co-authored-by: vanillagorillaa <ntmccoy@yahoo.com>
Co-authored-by: vanillagorillaa <31773928+vanillagorillaa@users.noreply.github.com>
* block lkas
* taco time
* local changes
* start
* tx checks
* counter + vehicle moving
* support big can fd
* check crc
* add torque to rx checks
* tests
* little more
* little more
* get some misra coverage
Co-authored-by: Comma Device <device@comma.ai>
Co-authored-by: Adeeb Shihadeh <adeebshihadeh@gmail.com>
* safety for non-longitudinal
* flip around param for easily replaying old logs on new panda
* fix misra: a function parameter should not be modified
* safety
* the toyota tests all share common messages
* fixup tests
* update comment
* same as tesla test
* check if subset
* update comments
update comments
* make safety_param unsigned
* final one
* uint32_t
* change flags as well
* Revert "change flags as well"
This reverts commit ed8897dd86.
* unsigned
* update health packet version
update health packet version
* update struct H->I
* bump health version
* actually used
* safety mode for body
* move to 27
* dmm...
* misra..
* add faw to safety list
* missing safety modes in python lib
* dmm
* change address to 250
* add 0x1 addr for can flasehr
* whitespace
* alternative experiences
* not unsafe
* more renames
more renames
* not yet true
* I think we import from panda now
* update comments and test
* not needed
* bump health pkt version
Co-authored-by: Adeeb Shihadeh <adeebshihadeh@gmail.com>
* Add RTC with LSI for BP, GP, WP
* disable jenkins temporarily, REVERT!
* experiments
* cleanup is still needed
* cppcheck unused suppress
* raise deepsleep limit timeout to 120sec
* more experiments on usb_enumerated
* continue
* soft_disconnect
* almost done
* not enough
* no ignition
* still don't like it..
* rename to has_rtc_battery
* clock_source on the way!?
* delay 3 sec
* works on C3, needs test on C2
* And this is for C2
* disable bootkick
* misra 10.4
* ..
* ..
* set power state the right way
* change that
* seems don't need that? check on C2/C3
* partially works on RP...
* comments (will work after rebase)
* change fault name
* switch to manual activation mode
* Revert "disable jenkins temporarily, REVERT!"
This reverts commit 578d425fa7.
* my dear pedal!
* add unsafe_mode to health packet
this compiles
update health packet
fixes
ahh forgot to set it!
not actually needed
update indices
* fix struct
Co-authored-by: Willem Melching <willem.melching@gmail.com>
* cleanup python lib
* remove wifi leftovers from firmware
* few spots in firmware
* forgot
* remove usb to wifi test
* linter
* more cleanup in flasher.h
* more found
* check in tests too
* linter
* tesla safety cleanup + long WIP
* more long safety
* longitudinal safety tests
* fix misra
* add safety for main bus DAS_control
* acc_state is not enabled
* fix tests
* we don't want this
* fix Tesla common test
* python: disable power save by default when setting safety mode
* no need to set power save manually
* Update python/__init__.py
Co-authored-by: Adeeb Shihadeh <adeebshihadeh@gmail.com>
* Extend ISO-TP subsequent frame timeout, add response pending timeout and extra debug info
* Change response_pending to local variable, move response_pending_timeout to UdsClient, update ISO-TP debug output
* Set UDS request pending timeout to 6 seconds (ISO 14229-2:2013 section 7.2 recommended value + 1 second latency)
* manage response pending in single location
* more generous response pending timeout
* add tx timeout
* fix lint error
* fix rx addr for 29 bit addrs
* fix linting issue
Co-authored-by: Martin Lillepuu <martin@mlp.ee>
* H7 drivers
* Include H7 into the code
* fix flash write for H7
* get serial from flasher.h from F4 and H7
* flash.sh and recover.sh for gen3
* add set_data_speed for BRS CAN FD
* build all fws
* gen3 to panda lib
* gen3 name in scons project
* disable fd can and brs
* gen3 to CI tests
* jenkins fix for new tests and build_all
* fix pedal test
* pedal in panda tests again...
* cleanup llfdcan.h
* cleanup clock.h
* Add LDORDY bit check instead of delay
* missing define in stm32h735xx.h lib
* board_id helper
* enable debug detection again
* clean gpio inits
* fix board_id helper, make cleaner
* comment MCUs in stm lib for faster misra
* target MCU
* misra-5.5
* improve headers and misra speed
* cleanup CI tests
* change naming from gen3 to h7
* readable if statement
* cleanup llusb.h
* only cycle one transceifer in bus-off
* move unused funcs to common header
* bus_off_err reset
* misra 10.4 fdcan
* extern to can_data_speed variable
* limit can_data_speed array size to 3
* reinit fd can on data speed change
* Improve test with ELM327 and extaddr check
* bugfix for fdcan
* panda python config naming
* abstracted init request in llfdcan
* misra fdcan
* Improve llusb.h for H7
* Remove non-EON panda build
* missed that
* fixup readme
* more readme
* simplify ci
* add USB command to disable heartbeat checks in debug mode
* clean that up too
* more cleanup
* fix path
* disable heartbeat in set_safety_mode
* more red
* remove one more EON ref
* remove unused wifi tests
* remove that one too
* no bootmode from ESP
* clean that up
* remove two more wifi tests
* remove boardesp and esptool
* esp_gps -> gps
* missed those
* remove esptool refs
* remove esp certs
* no more wifi
* that was old
* cleanup jenkins dockerfile
* fix linter
* remove more wifi refs
* clone panda jungle from github
* no copy
* always default esp to off
* k-line slow init
* k-line slow init LED bit blink
* fix misra violations
* better names for k-line methods
* debug prints match names
* switch to timer
* use TIM4 until I figure out TIM5
* tickle faster
* fix bit bug and add stop bit
* TIM5 working
* USB return after addr sent
* fix l-line reset
* fix misra violations
* blink for the ones instead of the zeros
* k-line 5 baud fault type
* lin check
* use TIM5 or wakeup
* better names
* enable UART RX interrupts
* update debug prints for python3
* improve kline functions and fix checksum
* k-line wake-up conforming to KWP2000 fast init
* fix timing
* toggle k and l line together by default
* k-line wakeup using timer
* k and l were flipped
* fix misra compliance
* fix W391
* E262
* E703
* W293
* some E
* E231
* some more E
* E225
* more E
* E252
* no tabs
* more tabs
* E701
* uds.py
* almost all of them
* only e265 left
* not sure why this is triggering on commented out code
* ignore esptool
* Add pre commit checks
* untested but should work
* fix typo in dockerfile
* add sqlite
* add pylintrc to ignore usb1 members
* Typo in stage name
* Move to requirements
* wait for tx slots before clearing nak
* fix bootstub
* Fixed misra
* Cleanup
* Added bulk write test to test USB NAK on bulk CAN messages
* Added automated bulk tx test
* Fixed linter
* Fixed latency test influence
* Added timeout to python API
* Disabled can write timeout in bulk write test
Co-authored-by: Robbe <robbe.derks@gmail.com>
* Align with VW Community port 0.7.4-devel
* Import of PQ35/PQ46/NMS safety work
* Add safety replay drive for PQ35/PQ46/NMS
* Unwind community port hax for upstream, bump Panda ver
* Update comment
* Reduce whitespace diff
* Reduce whitespace diff
* Don't test the drive until it's uploaded
* Propitiate MISRA
* Ixnay on the VERSION LF
* Remove VERSION LF, update safety_replay with PQ drive
* Freshen cereal ref to include fields used in VW PQ test drive
* Remove superfluous return
* Bypass Docker caching issue
* Checkpoint Panda refactoring updates
* Rename MQB safety tests in preparation for PQ
* Refactor MQB tests, add missing torque test
* Bring in MQB init without CRC LUT setup
* Fix to ACC_06 test case
* Fix to ACC_06 test case
* Tweak comment for clarity
* Drop superfluous return
* Commands to get signature from panda
* does this make misra happy?
* Can I do this in misra?
* this works and makes misra happy
* Add jenkins test for get signature
* Remove comments
* Add comment about code size
* Fix firmware file path
* Exit power saving also for CAN based ingition detection and replace interrup with simple state machine. a bit of delay it's fine
* bug fixes and also CDP set on start
* sorry misra
* move comment
* typo
* remove ignition interrupts
* Power saving state machine should be done by boardd, which also sets safety modes and usb power modes
* typo
* Added usb command for power save state setting
* Added power save enabled packet
* Added power_save_enabled to python lib too
* Added uno
* Added usb switch support
* Added PWM and IR power functions
* Implemented bootkick
* Added uno as a new hw type
* Bumped version
* Added fan control and tach readout
* WIP: RTC support
* Working RTC
* Fixed python
* Misra compliance
* Added USB control messages for fan/IR power
* Added USB commands + tests for fan & IR control. Fixed bootstub and pedal compilation
* Added IR and fan to power saving mode
* Changed defaults
* Fix safety considering uno
* passing safety now
* Minor UNO tweaks
* Fixed version
* More minor temporary tweaks
* Removed usb load switch from uno
* Added power control for shutting down the fan completely
* Disable IR LEDs by default
* Fixed linter issue
* Linter fix#2
* make ignition logic common for all cars
* ignition_can is not a safety thing. move it to can drivers
* bump version
* gm safety passive is deprecated
* move tx 1 on logic into board specific headers.
* Added pyflakes and Pylint for python
* Actually run linter in CI
* some simple pyflakes changes
* Add flake8 to panda reqs for linter test
* flake8 errors are fixed
* run flake8 in regression tests
* meant to run flake8
* hack to ignore unused import
* bug
* fix bugs in tucan_loopback
* Another fix by using set_safety_mode
* added pylintrc file
* more fixes and enabled pylint as well
* Fix pylint in circleci
* added linter to readme
* Panda safety code for Volkswagen, Audi, SEAT, and Škoda.
* First pass at MISRA compliance.
* Second pass at MISRA compliance.
* Fix scope of violation boolean.
* MISRA doesn't care for implicit cast of unsigned int to boolean.
* Remove superfluous newline.
* Remove unused VW ignition hook code, preserve commentary.
* Add 50% padding to max delta check.
* Add 50% padding to max delta check.
* Add clarity around the origin of our safety constants.
* Update test RT delta to match safety.
* Jenkins test refactor and black panda addition
* Added HW types needed by previous commit
* Fixed ignition interrupts when not on EON build
* Added functions for load switches
* More test scripts for black panda
* Added NONE power mode to the code
* Fixed race condition when setting GPIO pins was interrupted.
* Added relay test script
* Fixed flashing with critical sections and GPS load switch
* Fixing critical depth after reboot
* Made the loopback test asserting
* Made critical depth a local variable to avoid race conditions
* Added GPS to power savings mode
* Fixed DFU mode on white panda and bumped version
* Fixed PEDAL_USB compilation error
* Fixed misra compliance of new critical depth code
* Cleaned up heartbeat logic in the testing code. Re-added ALL_CAN_BUT_MAIN_SILENT. Bumped version. Improved critical section code.
* Fixed DFU flashing (once again)
* Fixed VERSION
* Added relay endurance test
* Changed to alloutput on ELM mode for fingerprinting.
* Fixed minor remarks
* late usb
* Added type support for black panda
* Added harness presence and orientation detection
* harness relay driving code
* Added intercept support in black panda code. Switched around can0 and can2
* Disable ADCs after orientation detection. Ignition interrupts via harness
* WIP: Hardware abstraction layer + black panda bringup
* Fixed bootstub build
* Fixed bootstub for pedal
* Fixed infinite loops
* Got CAN buses working on white again
* Fixed pedal build and black can interfaces
* Got CAN buses working on black panda
* Finished loopback test for black panda
* Erase all flash sectors on the panda. Increased binary limit. Added extra python functions.
* Fixed python
* Made new code MISRA compliant
* Cleaned up ignition. Fixed build
* Fixed health packet
* Fixed CAN mode on black bug. Changed OBD to switch on ELM mode
* Fixes from Github review
* Fixed MISRA issue for pedal
* Fixed failing gmlan tests
* ELM327 safety: allow diagnostic on all buses
* Cleaned up EON relay code
* delete only 3 sectors instead of 11 to allow a new build to be flashed. Much faster to flash
* Removed CAN only can0 output mode. Does not make sense on black panda due to reversibility issues.
* Added heartbeat logic for EON code on panda. Go to NOOUTPUT if EON does not send a heartbeat for 5 seconds.
* Remove all CAN buses live on EON startup. Shouldn't be necessary to have this separate case
* Formatting
* Added file I forgot to push
* Added heartbeat to testing code to make sure EON tests don't fail. Should probably find a better way to do this though. Heartbeat thread didn't work, concurrent USB connection issues...
* Safety: support black panda for Honda Bosch
* Disable OBD2 if setting to NOOUTPUT mode
* Run safety tests for all hw_types
* Fail test if subtest fails
* fix safety tests
* Initial version of L-Line Relay
* lline relay fix build, add to health
* Add lline relay to safety
* Lline relay fix build
* Fix tests
* Add lline safety init. Dont fwd with relay closed
* Turn on relay with CAN
* relay hook
* More reliable lline relay
* Longer LLine timeout
* Only turn on wifi if not eon
* Dont disable ESP in early
* Allow CAN to be turned off
- CAN is turned off via USB.
- CAN is turned on when either try to transmit or can is received
- If only transmit is asleep, all messages should send okay
- If receive is alseep, will miss first message while waking up
- Sometimes will report error on second message while CAN perif wakes up
- Saves 130mW!
* Power Saver Mode
- Gray Panda power consumption 650mw -> 325mW
- Turns off CAN, GMLAN, LIN, GPS when no activity for 10s
- No acitvity is no CAN send, CAN Recv, Write to GPS
* Fix power_saving to better turn off can
- On some cars when the can is turned off, it triggers a wakeup.
Delaying the automatic wakeup seems to fix this
* Don't save power in pedal
* Fix relay clicking on startup
* Fix duplicate include
* consistent relay setting
* relay_status can be added when needed, as it's started_alt was consumed in other places
* need to skip forwarding only if relay control is claimed
* unneded change
* make lline_relay.h not depending on can.h
* less spaghetti I guess
* less lines
* reset pedal changes
* no unused input
* update version
* Improve panda automated testing
* begin testing both white and grey panda
* Improve wifi reliability
* First commit for docker
* Fix usb devices not showing up on reconnect
* Add tests for two pandas, latency and throughput
* Add Jenkinsfile
* Allow flashing release on wifi
* Fix Jenkins stuck in DFU mode and docker container running
* Add pandaextra from xx to docker
* Need more time for ST to restart, sometimes
* Add xml output to tests
* Try making wifi more reliable
* Fix infinite loop in ping
* Check connected after flash
* Cleanup two panda tests
* Try fixing failing test with check after udp
* Try to fix with sleep
* Temporarily run just 5 and 6
* Cleanup
* Desperate times call for desperate measurse
* BUGFIX: power saving when rx only
* Fix failing when white panda is first after udp
* Test both Dev and EON build
* Jenkins test results for both builds
* Better test case naming
* Only turn on wifi if not eon
* Dont disable ESP in early
* Allow CAN to be turned off
- CAN is turned off via timeout
- CAN is turned on when either try to transmit or can is received
- If only transmit is asleep, all messages should send okay
- If receive is alseep, will miss first message while waking up
- Sometimes will report error on second message while CAN perif wakes up
- Saves 130mW!
* Power Saver Mode
- Gray Panda power consumption 650mw -> 325mW
- Turns off CAN, GMLAN, LIN, GPS when no activity for 10s
- No acitvity is no CAN send, CAN Recv, Write to GPS
* Fix power_saving to better turn off can
- On some cars when the can is turned off, it triggers a wakeup.
Delaying the automatic wakeup seems to fix this
* Don't save power in pedal
* Cleanup power saving
* Chrysler safety model and tests.
* fix comments
* when ACC is canceled, disallow controls
* update SAFETY_CHRYSLER value in Python API and add other SAFETY values
* Implement webusb and winusb 2.0 specs
* Add missing constants
* Refactor string system, add support for USB2.1
* Uncapitalize the panda
* Add USB 2.0 extension descriptor and device qualifier getter
* Sleep during reconnect process to be more reliable
* Disable compiler optimizations because they break SPI coms
Adeeb Shihadeh
Shane Smiskol
Willem Melching
Comma Device
Robbe Derks
Greg Hogan
Igor Biletskyy
Igor Biletksyy
Dange
Jason Young
George Hotz
Adeeb
openpilot laptop
bkralik
Adeeb
Shreyansh Chandak
rbiasini
Andre Volmensky
dekerr
George Hotz
Nigel Armstrong
Drew Hintz
George Hotz
Chris Vickery
Jennifer Strange