* Add RTC with LSI for BP, GP, WP
* disable jenkins temporarily, REVERT!
* experiments
* cleanup is still needed
* cppcheck unused suppress
* raise deepsleep limit timeout to 120sec
* more experiments on usb_enumerated
* continue
* soft_disconnect
* almost done
* not enough
* no ignition
* still don't like it..
* rename to has_rtc_battery
* clock_source on the way!?
* delay 3 sec
* works on C3, needs test on C2
* And this is for C2
* disable bootkick
* misra 10.4
* ..
* ..
* set power state the right way
* change that
* seems don't need that? check on C2/C3
* partially works on RP...
* comments (will work after rebase)
* change fault name
* switch to manual activation mode
* Revert "disable jenkins temporarily, REVERT!"
This reverts commit 578d425fa7ba256f513c1c6ca54a00d69d78f53e.
* my dear pedal!
* add unsafe_mode to health packet
this compiles
update health packet
fixes
ahh forgot to set it!
not actually needed
update indices
* fix struct
Co-authored-by: Willem Melching <willem.melching@gmail.com>
* cleanup python lib
* remove wifi leftovers from firmware
* few spots in firmware
* forgot
* remove usb to wifi test
* linter
* more cleanup in flasher.h
* more found
* check in tests too
* linter
* tesla safety cleanup + long WIP
* more long safety
* longitudinal safety tests
* fix misra
* add safety for main bus DAS_control
* acc_state is not enabled
* fix tests
* we don't want this
* fix Tesla common test
* python: disable power save by default when setting safety mode
* no need to set power save manually
* Update python/__init__.py
Co-authored-by: Adeeb Shihadeh <adeebshihadeh@gmail.com>
* H7 drivers
* Include H7 into the code
* fix flash write for H7
* get serial from flasher.h from F4 and H7
* flash.sh and recover.sh for gen3
* add set_data_speed for BRS CAN FD
* build all fws
* gen3 to panda lib
* gen3 name in scons project
* disable fd can and brs
* gen3 to CI tests
* jenkins fix for new tests and build_all
* fix pedal test
* pedal in panda tests again...
* cleanup llfdcan.h
* cleanup clock.h
* Add LDORDY bit check instead of delay
* missing define in stm32h735xx.h lib
* board_id helper
* enable debug detection again
* clean gpio inits
* fix board_id helper, make cleaner
* comment MCUs in stm lib for faster misra
* target MCU
* misra-5.5
* improve headers and misra speed
* cleanup CI tests
* change naming from gen3 to h7
* readable if statement
* cleanup llusb.h
* only cycle one transceifer in bus-off
* move unused funcs to common header
* bus_off_err reset
* misra 10.4 fdcan
* extern to can_data_speed variable
* limit can_data_speed array size to 3
* reinit fd can on data speed change
* Improve test with ELM327 and extaddr check
* bugfix for fdcan
* panda python config naming
* abstracted init request in llfdcan
* misra fdcan
* Improve llusb.h for H7
* Remove non-EON panda build
* missed that
* fixup readme
* more readme
* simplify ci
* add USB command to disable heartbeat checks in debug mode
* clean that up too
* more cleanup
* fix path
* disable heartbeat in set_safety_mode
* more red
* remove one more EON ref
* remove unused wifi tests
* remove that one too
* no bootmode from ESP
* clean that up
* remove two more wifi tests
* remove boardesp and esptool
* esp_gps -> gps
* missed those
* remove esptool refs
* remove esp certs
* no more wifi
* that was old
* cleanup jenkins dockerfile
* fix linter
* remove more wifi refs
* clone panda jungle from github
* no copy
* always default esp to off
* k-line slow init
* k-line slow init LED bit blink
* fix misra violations
* better names for k-line methods
* debug prints match names
* switch to timer
* use TIM4 until I figure out TIM5
* tickle faster
* fix bit bug and add stop bit
* TIM5 working
* USB return after addr sent
* fix l-line reset
* fix misra violations
* blink for the ones instead of the zeros
* k-line 5 baud fault type
* lin check
* use TIM5 or wakeup
* better names
* enable UART RX interrupts
* update debug prints for python3
* improve kline functions and fix checksum
* k-line wake-up conforming to KWP2000 fast init
* fix timing
* toggle k and l line together by default
* k-line wakeup using timer
* k and l were flipped
* fix misra compliance
* fix W391
* E262
* E703
* W293
* some E
* E231
* some more E
* E225
* more E
* E252
* no tabs
* more tabs
* E701
* uds.py
* almost all of them
* only e265 left
* not sure why this is triggering on commented out code
* ignore esptool
* Add pre commit checks
* untested but should work
* fix typo in dockerfile
* add sqlite
* add pylintrc to ignore usb1 members
* Typo in stage name
* Move to requirements
On Windows, setAutoDetachKernelDriver is not supported (http://libusb.sourceforge.net/api-1.0/group__libusb__dev.html#ga5e0cc1d666097e915748593effdc634a) and causes libusb to get stuck (simple try-catch is not working). This prevents any issues when running both at native windows python and cygwined python...
* wait for tx slots before clearing nak
* fix bootstub
* Fixed misra
* Cleanup
* Added bulk write test to test USB NAK on bulk CAN messages
* Added automated bulk tx test
* Fixed linter
* Fixed latency test influence
* Added timeout to python API
* Disabled can write timeout in bulk write test
Co-authored-by: Robbe <robbe.derks@gmail.com>
* Align with VW Community port 0.7.4-devel
* Import of PQ35/PQ46/NMS safety work
* Add safety replay drive for PQ35/PQ46/NMS
* Unwind community port hax for upstream, bump Panda ver
* Update comment
* Reduce whitespace diff
* Reduce whitespace diff
* Don't test the drive until it's uploaded
* Propitiate MISRA
* Ixnay on the VERSION LF
* Remove VERSION LF, update safety_replay with PQ drive
* Freshen cereal ref to include fields used in VW PQ test drive
* Remove superfluous return
* Bypass Docker caching issue
